碳纤维/ 环氧树脂层压板的孔隙问题

总结了国内外关于碳纤维/环氧树脂层压板孔隙的形成机理、检测方法、影响因素及孔隙对复合材料力学性能的影响.结果表明,孔隙对复合材料层合板的强度和疲劳寿命有不利影响,并且孔隙对水的渗透和环境因素非常敏感,孔隙的存在促进了水分的吸收,且吸湿可导致材料强度下降.提出湿热环境下孔隙对复合材料性能影响是未来研究方向之一.     

环状针刺C/C复合材料的压缩性能及破坏机理

以碳纤维针刺毡为预制体,采用CVI致密工艺制作准三维C/C薄壁回转体,具有各向异性的力学性能.本文主要对三个主方向的材料压缩性能及破坏机理进行了研究讨论.结果表明:轴向压缩与环向压缩性能相似具有较高的压缩模量.材料的径向压缩表现为假塑性断裂行为,在材料的断裂面上具有大量纤维及基体碎屑,材料发生剪切破坏及基体压溃破坏.材料的轴向压缩与环向压缩表现为脆性断裂行为,材料主要以分层劈裂方式破坏.     

一种铍合金材料的结构和性能

对国外某型号飞机所用的铍合金刹车材料进行了密度测试、结构观察、化学元素分析、力学、物理和摩擦性能表征,并与C/C、C/SiC复合材料和粉末冶金材料的相关性能作了对比,结果表明,粉末冶金铍合金材料密度低,力学和摩擦性能优异,是一种很有发展前途的刹车材料.     

热处理工艺对2A70铝合金自由锻件力学性能的影响

研究了不同热处理工艺参数对2A70铝合金自由锻件力学性能的影响。首先采用正交试验分析了各因素对两个目标值(抗拉强度、延伸率)的影响;然后利用极差分析方法分析试验结果,指出各个因素对力学性能影响的主次顺序,并确定最优的热处理生产条件。试验结果表明:通过锻件锻后增加退火处理、适当提高固溶温度和选用合适的时效保温时间,该合金的力学性能得到了较大的改善,在保证抗拉强度大于等于375MPa要求的同时,延伸率由4%提高到了8.5%。     

一种新的柔性蜂窝结构及其在变体飞机中的应用

变体色机要求机翼结构可以光滑连续地变形.机翼的蒙皮要有足够大的面内伸缩变形能力,同时还要有足够的面外承载能力.本文针对后缘变弯度机翼,设计出一种新的柔性蜂窝结构.研究了该柔性蜂窝的面内变形能力和形状参数的关系.仿真分析和试验验证表明,该柔性蜂窝结构具有足够的面内变形能力,变形后仍保持良好的面外承载能力,满足后缘变弯度机...     

Effects of process parameters on mechanical properties of abrasive-assisted electroformed nickel

A cathode mandrel with translational and rotational motion, which was supposed to obtain uniform friction effect on surface, was employed in abrasive-assisted electroforming for revolving parts with complex profile. The effects of current density, translational speed and rotational speed on the deposit properties were studied by orthogonal test. The tensile strength, elongation and micro hardness value were measured to find out how the factors affected the properties. The optimized results show that changes of current density affect the tensile strength of nickel layer most, while translational speed has the most remarkable influences on both elonga-tion and micro hardness. The low rotational speed affects the properties least. In this experiment, a smooth nickel layer with tensile strength 581 MPa, elongation 17%and micro hardness 248HV is obtained by the orthogonal test.     

A novel surrogate modeling strategy of the mechanical properties of 3D braided composites

In this paper, a surrogate-based modeling methodology is developed and presented to predict the elastic properties of three dimensional (3D) four-directional braided composites. Using this approach, the prediction process becomes feasible with only a limited number of training points. The surrogate models constructed using Finite Element (FE) method and Diffuse Approximation, reduce the computational time and cost for preparing experimental samples. In the FE model, multiscale method is applied to couple the computations of elastic properties at microscale and mesoscale. Subsequently, a parametric study is performed to analyze the effects of the three design parameters on the elastic properties. Satisfactory results are obtained via the surrogate-based modeling predictions, which are compared with the experimental measurements. Moreover, the predictions obtained from surrogate models concur well with the FE predictions. This study orients a new direction for predicting the mechanical properties based on surrogate models which can effectively reduce the sample preparation cost and computational efforts.     

Mg-Sc-Y三元合金的微观组织和力学性能

稀土元素作为重要的镁合金强化相元素,其多元添加产生的影响并未得到充分研究。在Mg-Sc二元系的基础上将Y作为第三元加入,制备了Mg-5Sc二元合金及Mg-5Sc-0.5Y,Mg-5Sc-1Y,Mg-5Sc-2Y,Mg-5Sc-3Y,Mg-5Sc-3.5Y(质量分数,%)5种三元合金,并通过光学显微镜(OM)、扫描电子显微镜(SEM)、X射线衍射(XRD)及室温拉伸等试验,研究了Y元素的加入对Mg-Sc二元合金微观组织和力学性能的影响。结果表明:Y元素在合金中的主要存在形式为固溶态,富集于晶界处。随着Y元素含量的提升,合金晶粒度显著减小,屈服强度和硬度大幅提升,Mg-5Sc-3.5Y的屈服强度相比Mg-5Sc提升了约50%。该强度的提升主要是由细晶强化和固溶强化引起的。     

PIP工艺制备SiC晶须增强SiCf/SiC复合材料的性能

以不同界面层厚度的SiC纤维为增强相,采用先驱体浸渍裂解工艺(PIP)制备SiC_f(PyC)/SiC复合材料,并在复合材料基体中引入SiC晶须,对其性能进行研究。结果表明:热解碳(PyC)界面层厚度约为230 nm时,SiC纤维拔出明显,SiC_f/SiC复合材料拉伸强度、弯曲强度和断裂韧度分别达到192.3 MPa、446.9 MPa和11.4 MPa?m^1/2;在SiC_f/SiC复合材料基体中引入SiC晶须后,晶须的拔出、桥连及裂纹偏转等增韧机制增加了裂纹在基体中传递时的能量消耗,使复合材料的断裂韧度和弯曲强度分别提高了22.9%和9.1%。     

低频电连接器检测方法研究CSCD

本文主要阐述了低频电连接器外观检测和电性能测试中的接触电阻、绝缘电阻和介质耐电压的检测方法及其注意事项,提出为满足武器系统对低频电连接器耐恶劣环境、高可靠的特殊需求,有效保证武器型号系统中电连接器的质量,必须规范低频电连接器外观及电性能指标检测标准。本文可为从事低频电连接器检测工作的人员提供参考。